Currently, syringe dispensing is being replaced by jet dispensing. so-called jet (jetting), is new technology, which uses alternative syringe nozzle to solve the many difficult issues. Jetting nozzles may need to fill the bottom of the top of the dispensing device without the need to reach the top surface of the following locations. Jetting nozzles in the entire circuit board side along the x, y direction, without vertical movement.
Dispensing syringes with different end of the nozzle is not sufficient glue to form a continuous stream, and replaced after a second injection of 200 points or more accurate measurement of the gel point. Along with the standard nozzle movement, the gel-point line can form a variety of needs and patterns, solid line, dotted line,Ce lien n'est pas visible, veuillez vous connecter pour l'afficher. Je m'inscris!, etc., and other various graphics. after each injection are precise control of spray formed by a minimum diameter of the gel-point up to 0.33mm, which for coating plastic patch into place that require precise control of the area of the occasion is very important.
Jet technology is the glue at a faster rate from the nozzle, relying on the momentum of the glue from the glue nozzle. Each spray will spray out a certain amount of glue. of the prevailing jet frequency is 100 Hz to 200 Hz, but will soon reach 1000hz. Jet Dispensing with needles, there are several different dispensing. When the glue from the nozzle when the glue had prior contact with the substrate and the nozzle separation. for every point of injection to a plastic substrate to form points, lines and graphics. dispensing position in the process of moving, dispensing,Ce lien n'est pas visible, veuillez vous connecter pour l'afficher. Je m'inscris!, there were no Z-axis movement,Ce lien n'est pas visible, veuillez vous connecter pour l'afficher. Je m'inscris!, so saving a considerable amount of time. needle dispensing, the mechanical hand in the X, Y, Z axis movement, the glue flow from the needle out of contact with the substrate, the substrate by gravity and surface tension to separate the glue from the needle. after the completion of each dispensing along the Z axis has a significant movement, then move to the next dispensing position.
LED technology in the market also benefited from the spray. spray coating process can include silicone, UV curable conductive adhesive such as phosphorus-doped wide range of optical materials can be carried out in high-speed dispensing position and dispensing precise control of glue. spray can improve the accuracy of the value of a high yield of high-power LED devices. used in the production of white light, fluorescent powder and mixed glue dispensing, its consistency has been well improved.
Dispensing syringes with different end of the nozzle is not sufficient glue to form a continuous stream, and replaced after a second injection of 200 points or more accurate measurement of the gel point. Along with the standard nozzle movement, the gel-point line can form a variety of needs and patterns, solid line, dotted line,Ce lien n'est pas visible, veuillez vous connecter pour l'afficher. Je m'inscris!, etc., and other various graphics. after each injection are precise control of spray formed by a minimum diameter of the gel-point up to 0.33mm, which for coating plastic patch into place that require precise control of the area of the occasion is very important.
Jet technology is the glue at a faster rate from the nozzle, relying on the momentum of the glue from the glue nozzle. Each spray will spray out a certain amount of glue. of the prevailing jet frequency is 100 Hz to 200 Hz, but will soon reach 1000hz. Jet Dispensing with needles, there are several different dispensing. When the glue from the nozzle when the glue had prior contact with the substrate and the nozzle separation. for every point of injection to a plastic substrate to form points, lines and graphics. dispensing position in the process of moving, dispensing,Ce lien n'est pas visible, veuillez vous connecter pour l'afficher. Je m'inscris!, there were no Z-axis movement,Ce lien n'est pas visible, veuillez vous connecter pour l'afficher. Je m'inscris!, so saving a considerable amount of time. needle dispensing, the mechanical hand in the X, Y, Z axis movement, the glue flow from the needle out of contact with the substrate, the substrate by gravity and surface tension to separate the glue from the needle. after the completion of each dispensing along the Z axis has a significant movement, then move to the next dispensing position.
LED technology in the market also benefited from the spray. spray coating process can include silicone, UV curable conductive adhesive such as phosphorus-doped wide range of optical materials can be carried out in high-speed dispensing position and dispensing precise control of glue. spray can improve the accuracy of the value of a high yield of high-power LED devices. used in the production of white light, fluorescent powder and mixed glue dispensing, its consistency has been well improved.
